Ultraschall-Drehmomentschweißgerät für 4680 Zellen

No

Item

Specify

1

Substrate (thickness)

The current collector thickness is 0.2-0.4mm aluminum strip (1060Al), and the thickness of aluminum is 2-4mm (1060Al) in kind

2

Reference welding sample and welding mode

Reference sample welding

3

Welding head design

Probe design. The diameter of the welding needle is 4.0-4.50mm, and the length of the welding needle is 85mm

4

Welding parameter

(1) Welding time: within 0.1-0.8S (adjustable program 0-60S).

(2) Welding pressure: within 0.1 ~ 0.6Mpa.

(3) Resonance frequency: 20KHz±200Hz.

5

Head stroke

It depends on the design

6

Electric power frequency parameter

(1) Maximum input power: 3000VA.

(2) Ultrasonic frequency: 20KHZ±200Hz. (Automatic tracking).

(3) The amplitude is adjustable.

(4) Welding mode: time mode, energy mode, depth mode.

7

Equipment control mode

(1)Hand motor operation control mode: double button delay 1-3S start control.

(2)Supporting production line for IO line signal control.

8

Welding ability and acceptance specification

(1) No virtual welding, welding through, leakage, good welding effect, layer upon layer penetration.

(2) Welding qualified rate: 99.7%. The first-pass rate is 99.7%. The user must ensure that the products, processes, and materials are consistent, that the operators have received professional training from the supplier, and that the demander maintains the equipment on a weekly basis.

(3) In terms of technology, the welding effect meets the requirements of the manufacturer and the production capacity is the main measure index.

(4) The operator must test welding every day more accurate work, when the quality department approved before mass production.

(5) Ultrasonic up and down pole wear and viscous production is not within the scope of the fault.

9

Designed service life of equipment

(6) Overall structure: ultrasonic generator, ultrasonic transducer system, ultrasonic up and down acoustic pole, pneumatic components, frame, workbench, etc.; (Hand model with workbench, work for production line do not have workbench).

(7) The designed service life of the equipment shall be subject to the purchase contract.

10

Model reference

(1) Welding machine generator size (length x width x height): (Specific installation size attached drawings)

(2) Welding machine head size (top: length x width x height): (Specific installation size attached with the drawing)

11

This section describes the system

I.Introduction of digital intelligent generator:

(1) Circuit characteristics reserved MES upload interface (using 485/TCp communication interface).

(2) Welding mode time mode, energy mode, continuous mode and depth mode.

(3) Protection system

(4) Das Lesen von Daten ist für Benutzer praktisch, um mehrere Schweißprozessparameter zu speichern und sie bei Bedarf direkt abzurufen.

II. Spezialstahlkonstruktionskopf:

(1) Präzise und stabile Maschinen, ausgestattet mit einem Sicherheitsschutz zur optischen Augenerkennung.

(2) Ausgestattet mit integriertem Kühlsystem.

Präzise Führungsstahlstruktur, Drehmomentwiderstand, sorgen für schnelle und stabile Bewegung.

III. Ultraschall-Auf- und -Ab-Akustikpol (Schweißkopf), streng ausgewählter importierter Schnellarbeitsstahl, Verschleißfestigkeit, hohe Temperaturbeständigkeit, gute Zähigkeit, hohe mechanische Steifigkeit, geringe Verformung nach der Wärmebehandlung, daher ist die Ultraschall-Ausgangsfrequenzkonsistenz hoch.

Produktname

Modell

Ultraschallgenerator

20 kHz

Ultraschallkopf

20 kHz

Ultraschallsonde

Φ4,5–85 mm

Zellwerkzeuge

Nicht standardmäßige Anpassung